Technological innovations are really surprising, especially when it comes to the practical side of life. More recently, people did not know the schemes for obtaining profitable energy, which makes it possible to refuse expensive electricity. Agree, now alternative sources are available to everyone and it would be great to use them.
Innovative solar panels for heating a house are gradually but persistently being introduced into our everyday realities. But before you go to the store for them, you should weigh the pros and cons, otherwise you can purchase a completely inappropriate model. In order to prevent this from happening, we will reveal the secrets of choosing these devices.
In addition, from our material you will learn the design features of solar collectors, as well as find step-by-step instructions for installing solar cells. For ease of perception, the material is accompanied by thematic photographs and videos.
The principle of using solar energy
Often, faced with the need to install solar panels, a person wonders about the feasibility of the enterprise. Because in most cases the percentage of sunny days loses significantly to the same cloudy value.
A similar ratio is typical for the regions of the middle zone, and the climate of the northern regions is characterized by an even greater number of cloudy days.
The insufficient number of sunny days is directly related to the efficiency of the devices that process the energy of the earth. As a result, exposure to sunlight to the surface of the battery is reduced. This process is called insolation.
Solar panels can be used in heating systems as a coolant or energy supplier to power appliances
Its essence lies in the fact that any plane, regardless of its purpose, takes on a certain amount of solar energy. In the southern regions, the amount is naturally higher, which makes the installation of solar panels more relevant.
However, as practice shows, the market for technological equipment in the field of solar energy synthesis is constantly improving its products, so modern solar cells in solar panels function perfectly even in areas with a low level of insolation.
The distribution of solar activity on the example of a map of Russia. A higher coefficient is characteristic of the southern regions (+)
Weighted Installation Approach
Before you organize a solar heating system, you should find out the disadvantages and strengths of the structure, powered by solar energy.
This knowledge is needed to better perceive the differences between equipment and analogues and to evaluate the rationality of the device and assess the feasibility of the construction.
The most significant factors are:
- Efficiency. Real efficiency when converting solar energy into electrical energy. While the energy of solar cells is almost five times more expensive than conventional electricity.
- Seasonality of application. Solar panels will be able to work efficiently only in the absence of obstacles to sunlight, including high cloud cover.
- Weak accumulation scheme. In most cases, the energy received must be consumed immediately. To accumulate and store it, quite voluminous drives are needed, the placement of which will require an impressive area.
- The need for auxiliary energy. In winter, solar panels will not be able to supply enough heat to heat a house.But can be a useful addition to the boiler in case of sunny weather.
- The feasibility of construction. At the moment, the payback of solar panels is much to be desired. Installing them justifies itself only in areas that are not connected to centralized networks. Where there is no alternative to solar devices at all.
There are hopes for the development and production of more affordable solar energy devices. There is confidence that once the construction of systems that process solar energy will become cost-effective.
True, if we take into account that the planet’s energy resources are gradually melting, then we can quite consider solar technology as a profitable, promising investment.
The solar complex is completely safe for the environment, does not emit toxic combustion products, does not upset the natural balance, does not require the burning of fossils and wood
However, now this is only an addition to the main sources of heat, but already has its own set of advantages.
Significant advantages of the solar complex:
- Long period of operation. Constructive simplicity guarantees a minimum of breakdowns. The panels can be accidentally damaged at the time of clearing the snow, but replacing the glass is quite affordable for do-it-yourself production.
- Wide variety of models. Devices produces a substantial number of foreign companies and individual representatives of domestic manufacturers. Price scatter allows you to choose the option “afford”.
- Individuality settings. The equipment can be configured taking into account all the vagaries of nature in a particular area.
- Cheap energy. More precisely, its complete gratuitousness is a quality that should not be taken literally because of the solid material consumption of the construction of solar panels.
- Outward appeal. Flat heating systems do not violate the architecture of houses, can be perceived as elements of creative design.
We found out that the solar complex can be a help in everyday life, supplementing traditional heating sources. In addition, given today's fuel prices, alternative energy helps save money, especially in the private sector.
Leading equipment manufacturers, in describing their products, in every way emphasize the absolute environmental friendliness of the system. Naturally, the process of photon energy conversion occurs without the participation of any combustible, toxic, or chemical explosive substances.
The solar panels located on the roof do not spoil the exterior of the house, do not take up much space
More globally, the widespread use of solar panels will certainly reduce the consumption of other energy sources, such as coal or natural gas. Of course, the situation with the environment in this case will improve qualitatively, and indefatigable bills for heating and combustible materials will remain in the past.
The efficiency of the panels is directly proportional to the amount of absorbed solar energy. But the technological aspect of different types of equipment allows you to increase or decrease productivity.
To increase system performance, it is recommended to install solar heating in symbiosis with other, more traditional methods of heating.
Do not worry about the fact that the solar collector will very soon fail. The average life of such equipment is about 15 years. The proper functioning of the photocells primarily depends on the region in which the installation is used.
As a rule, the most intense level of insolation puts the system under greater stress. Therefore, if the equipment is used in a temperate climate, it is quite capable of serving more than 15 years.
The life of solar panels is from 12 to 15 years. With proper care, they will last longer
Types of solar complexes
It has been experimentally proved that some substances are able to react more intensively to the effects of photons. Therefore, the technology for manufacturing solar panels is different.
Solar systems for domestic use are divided into 2 dominant types:
- Photoelectric Converters (silicon and film). They are groups of photocells connected in series or parallel to each other, converting solar radiation into electricity. The elements assembled into a single semiconductor system are called a solar panel, which supplies energy to electrically dependent heating devices.
- Solar collectors (flat, vacuum or tubular, collector-hubs or mirror). This is the most common type in everyday life, which receives solar energy and transfers it to the heating system in the form of electricity or a heated coolant.
In addition to these types, there are solar stations that produce energy on an industrial scale. For the private trader, they can serve as a centralized energy supplier.
A heating system with solar collectors provides for energy consumption immediately after it is received
The device of photovoltaic converters
The principle of operation of photovoltaic converters is based on the conversion of solar energy into its electrical type. They are produced in the form of modules on an aluminum frame or on a flexible polymer cloth.
In the first case, the top of the module is protected by high-strength glass, and the bottom by an insulating film. In the second case, both protective shells are made of polymers.
Photovoltaic cells are connected via conductive busbars, the function of which is to transfer energy to a battery or consumer. Contacts are connected to the buses, which serve to connect individual batteries to a complete system and to connect to consumers.
The principle of operation of photovoltaic converters is based on the ability of elements to convert solar energy into electrical energy
With a focus on the organization of silicon atoms, solar cells are divided into the following categories:
- Monocrystalline. Supplied with the purest silicon, the production technology of which has long been used in the manufacture of semiconductors. The essence of production is the artificial growth of a single crystal, which is ultimately cut into 0.2-0.4 mm thick plates. These are the cells of the future battery, which will require 36 pieces.
- Polycrystalline. In the manufacture of wafers are used, obtained from molten silicon after its slow cooling. Technology requires less energy and labor, because solar panels with polycrystals cost much less. Typically, these batteries have a standard bright blue color.
- From amorphous silicon. The technology of their production is focused on the principle of the evaporation phase. As a result of the evaporation process, a thin silicon film settles on the supporting element, which is wrapped on top with a transparent protective coating. This category of solar panels is called thin-film, installed on the walls of houses.
Monocrystalline batteries are the most efficient. Efficiency varies in the range of 14–17% depending on the model and the manufacturer. Polycrystalline lose to them by the criteria of efficiency, their efficiency on average 10-12%.
The most inefficient systems are amorphous silicon solar cells. They are designed to process scattered radiation, are installed on the walls of houses as a complement to more powerful systems located on the roof. Efficiency within 5-6%.
Polycrystalline Solar Options - Medium Price and Performance Offer
Based on the data received from leading manufacturers of solar modules, such as SunTech Power, it becomes clear that the efficiency of single crystals increases every year, and soon the efficiency can reach about 33%.
However, to date, the best performance indicators belong to the company's products. Sanyo. The peculiarity of these panels lies in the multilayer nature of the external element, which significantly increases efficiency, and the efficiency of solar collectors is 23%.
Due to the characteristic silicon processing procedure, the polycrystal structure contains undesirable formations that interfere with better absorption of solar energy.
Also, crystalline particles of the microstructure of the module are arranged in a chaotic manner with respect to each other, which complicates the sublimation of energy. As a result, the panel efficiency rarely exceeds 18%.
Sometimes there is a symbiosis of amorphous and poly- / single-crystal reservoirs. This is due to the fact that the normal operation of polycrystals requires intense sunlight, in contrast to amorphous panels. Therefore, the combination of the two technologies can be a way out.
There are tangible changes in the production of film systems. So, at the present stage, film helium modules based on cadmium and indium are quite common.
At each stage, silicon-hydrogen coating is constantly monitored, otherwise problems associated with operability are possible
It has been proven that cadmium absorbs sunlight very well, so many manufacturers in the field of solar energy have adopted it. As you know, the substance is radioactive, but do not worry because of the possibility of exposure, because the proportion of metal is not so large as to cause any harm to the atmosphere, not to mention man.
Indium semiconductor successfully produces 20% efficiency, ahead of cadmium. Due to the fact that indium is much more in demand in household appliances, namely in the production of LCD TVs, manufacturers often replace metal with another analogue - gallium.
Film solar equipment has a flexible structure, which greatly simplifies installation
Speaking about the advantages of polymer modules and film collectors as a whole, I would like to highlight a rather low price, compared with crystalline batteries, complete safety and environmental friendliness, thanks to the stable state of the chemical. substances. Also, flexibility and versatility can be added to the number of additional advantages.
Design features of solar collectors
The simplest option is a flat solar collector is a box-case, the front side of which is a blackened metal surface. Inside is a coil filled with water, a mixture of water with a non-freezing agent or air.
The bottom and walls of the box are closed by thermal insulation, the necessary conservation of the received energy within the battery.
A metal plate, coupled with tubes, collects and transfers the heated coolant to the heating system. This part is called the absorber. Most often, copper sheet is used for its manufacture, characterized by high thermal conductivity.
The outer side of the adsorber must be intensely black for maximum absorption of solar radiation.
Tubular type solar panels are a tube system or a coil with a metal plate on top
In order to prevent rays from reflecting from the metal surface of the adsorber, a durable transparent coating is installed on top. Usually these are tempered glass options with a minimum metal content.
Outside, a special optical coating is applied to it, which does not emit heat in infrared light. It helps to increase the productivity of the device, capable of heating water to 200 ° C.
Tubular panels are sensitive to atmospheric negativity.After heavy rainfall, especially hail, it is recommended to carefully check the integrity of the front cover of the collector.
Wind-blown foliage, dusty particles and fragments of branches can also damage the surface. Scratches and chips will lead to a sharp deterioration in equipment performance.
There are several options for installing solar panels, as during the operation, the developers gradually eliminated the shortcomings
The vacuum version is equipped with a multilayer tube designed according to the principle of a thermos. Such a system allows 95% better than previous models to keep warm.
In the lower part of the multilayer tube there is a liquid, which when heated by the sun turns into steam. A capacitor is mounted on top of this peculiar sealed bulb. Reaching its steam condenses and transfers heat to the system.
Heliopanels operating according to the vacuum principle are more effective than conventional tubular ones in areas with a small number of sunny days.
Hub collectors are equipped with a device with a mirror surface, which focuses the energy it receives on the surface of the absorber. The mirror area is larger than the same size of the absorber, thereby increasing the efficiency of receiving solar energy.
A mirror element can generally be concentrated on a dot or thin line without the slightest loss in performance.
Due to the device of the heat-receiving tube by the principle of thermos, the productivity of the device is almost doubled
The downside of concentrators is that they can only perceive direct radiation. Therefore, the latest developments are equipped with rotary tracking devices in order to eliminate or reduce the influence of this drawback.
Tracking devices force the collector to turn after the movement of the star to collect all its rays.
This is the most effective type of collector solar panels, which allows heating the coolant to a maximum temperature compared to other temperatures. True, they work well in desert areas, they cost a lot, because of which they are mainly demanded by production organizations.
The solar collector-hub works by focusing solar energy on an absorber having a smaller area
An interesting new solution was a spherical collector design that captures literally all the rays that it can perceive. It does not need to be equipped with a rotary mechanism, by the way, volatile and requiring connection to the mains.
The spherical design differs from the usual one in that it does not consist of separate tubes connected to the inlet and outlet pipes, but from a single screw heat receiver.
The receiver coil is filled with technical water, which when heated moves up the helical path and exits heated to the outlet pipe, and from there to the heating system.
After cooling, the coolant returns from the heating circuit to the inlet pipe of the spherical collector. The process is repeated.
Spherical shape allows full daylight to receive the sun's rays without the use of rotary mechanisms
A significant advantage of the spherical system is that heating occurs throughout the daylight hours. It does not need to be equipped with rotary mechanisms that need power. Thanks to the screw circuit, it is characterized by minimal energy losses in the pipeline.
All types of solar collectors belong to the category of seasonal auxiliary energy production systems. Depending on the model, their internal piping can hold up to 200 liters of liquid, and the minimum amount used in vacuum modules is about 60 liters.
It is quite possible to build a solar collector with your own hands. The site has a selection of articles on homemade solar systems.
We advise you to familiarize yourself with:
- How to make a solar collector for DIY heating - a step-by-step guide
- How to make a solar battery with your own hands: self-assembly instruction
Installation instructions for solar batteries
Panels belonging to the class of "flat", it is desirable to install in the summer season, when the level of insolation is higher. This will be the best option for the ratio of price and energy received, which means that the purchase of such solar collectors will fully justify all the money spent.
One way or another, the energy potential of the equipment allows it to be used in hot water and heating systems.
The energy conversion process is extremely sensitive to temperature extremes. This should be considered during installation. First of all, you need to make sure that the housing is thoroughly insulated, otherwise unforeseen malfunctions in the system may occur.
The heating system with solar panels is a closed circuit with a coolant circulating through it
For each region, an optimal equipment installation option is provided. The calculation is made on the degree of the same insolation. According to the rules of use, the collector must be positioned so that the angle of incidence of sunlight on its surface is 90 °.
Only in this case the efficiency of the system will be maximum. Absolute accuracy in the installation of panels can be achieved by measuring the latitude of the terrain.
An important factor will be the direction in which the panels are located. Due to the fact that the highest power level is achieved mainly in the middle of the day, it is worth orienting the panels in a southerly direction. Some deviations in the installation process are allowed, east or west, but not too much.
In addition, often a decrease in efficiency is observed against the background of shadows from trees on the collector panel. In winter it is recommended to increase the angle of inclination of solar panels, this will improve the level of system performance.
Step 1. Angle selection
The efficiency of the collectors primarily depends on the angle of the panel relative to the horizontal surface. For optimum light absorption, it is recommended to maintain a slope of 45 °.
The optimal angle of inclination of the solar panel depends on the season. Well, if the device is equipped with a device for adjusting the angle
The azimuth must be kept at 0 ° (direct south). Some deviations of 30-40 ° are allowed for better insolation. To increase stiffness, there is a special. aluminum constructions.
This is primarily characteristic for installing collectors on a sloping roof. They will prevent changes in the set parameters due to weather events, and the fast installation speed, using the mounting hooks and profiles, will save time.
Step # 2. Primary circuit construction
At the first stage, all heating components are installed: boilers, compressors, heat conductors, etc. For convenience, it is recommended to place the system elements in an easily accessible place. When installing the expansion tank, one should take into account the absence of obstacles between it and the collectors.
The temperature inside the tank is measured using a temperature sensor. It should be attached to the bottom of the tank.
The next step will be the organization of a ventilation system. When installing the circuit, it is necessary to create an air outlet coming out of the expansion tank. The best solution would be to put the communication on the roof. This will contribute to the regulation of pressure drops inside the heating system.
Solar panels - part of the heating system, which should include, in addition to them, boilers, centrifugal pumps, piping, etc.
The process of fluid movement inside the hot water supply depends on the circulation pump. It is recommended to be used only for systems with a closed type of water circuit.In addition, for the convenience of changing the fluid, the expansion tank should be equipped with a drain system. To do this, fit the crane somewhere in the bottom of the device.
Step # 3. We understand the features of operation
The solar system works from a network of 220 V. Each model has a unique connection scheme, which is supplied.
The wiring must be carefully insulated, and thermostats and all kinds of relays must be located in an exceptionally dry place. For better tightness, it is recommended to protect the equipment with a hydrophobic material.
Be sure to make sure the system is connected to ground. This will protect you from life-threatening situations.
Step # 4. Choosing a way to connect elements
Soldering of copper circuits and electrical parts must be done using a special solder paste. Before this, you need to clean the joints. This is best done with a steel brush.
Elements leading to the distribution tank (pipes, coils) are welded or screwed, having previously cut the thread. It is important to understand that a pipe with chilled liquid should approach the bottom of the tank, and with hot - to the top.
Step # 5. Solar installation
Preparatory stage: what needs to be prepared for installation.
Image Gallery
Photo from
The usual tools of the installer are useful for installing solar panels: drill, screwdriver, hammer, pliers, screwdrivers, wrenches
Two solar panels are needed as a power source for autonomous systems
The kit includes self-tapping screws, bolts with nuts, dowels, rivets, clamps - that is, any fasteners that may come in handy for mounting a metal profile and panels
Quickly and easily panels are mounted on specially selected fasteners, which are included in the assembly kit or purchased separately
Traditional set of mounting tools
Solar panels
Set of mounting tools for mounting
Aluminum profile elements for mounting
The following is the process of installing solar panels. Installation instructions for 2 panels are suitable for mounting any number of solar collectors: the installation principle does not change. The main thing is to find the area for installation.
Image Gallery
Photo from
As a suitable place the facade is chosen - the side facing the south side, that is, maximally lit by the sun
The decoration of the building is soft siding, so an additional stand is required for installation. The aluminum profile frame needs to be sized for solar panels
Aluminum is light enough not to damage the facade cladding, and durable to support the weight of the panels - 2 pieces of 8 kg
To raise the panels under the roof, an ordinary ladder is enough, but during installation it is necessary to comply with safety regulations
To simplify the fastening procedure, it is better to use the help of a second person: one holds the panel firmly, the second screws
After installing both panels, you should once again check the strength of all fasteners, since the structure will experience a load during strong wind and rain
First you need to connect the cables connecting the solar panels and the controller located on the outside of the house (under the panels)
The cables on the outside of the house through the hole in the wall are pulled inward - all that remains is to connect the battery terminals
Stage 1 - selection of installation site
Stage 2 - Panel Sizing
Stage 3 - Installing Aluminum Profile Stands
Stage 4 - panel elevation to the facade
Stage 5 - Attaching the First Solar Battery
Stage 6 - fixing the second solar battery
Step 7 - Connecting External Cable Lines
Stage 8 - connecting solar panels to the power supply system
The last step is system testing.
Additional information on the installation and connection of solar panels is presented in the articles:
- Schemes and methods of connecting solar panels: how to properly install the solar panel
- Connection diagram for solar panels: to the controller, to the battery and to the serviced systems
The use of solar panels in autonomous communication systems:
Demonstration of products of one of the leaders in the production of solar batteries:
The principle of design and operation of the vacuum manifold:
Solar systems every year improve performance in the conversion of solar energy. The developers already offer a huge selection of flat and tubular collectors using quartz spraying or single-crystal modules.
All this gradually updates alternative energy sources, as a result of which solar energy will soon become available to everyone.
Have experience connecting or using solar panels to heat your home? Or have questions about the topic? Please share your opinion, leave comments and participate in discussions. The communication unit is located below.