Satellite television is a technology of wide application, including application in everyday conditions, which has gained a high level of popularity. The digital equipment that forms the basis of the technology is a sophisticated electronics.
However, with all the complexity of the hardware, it is quite easy for the end user to figure out how to configure the satellite antenna tuner on their own, without involving a wizard.
This problem is solved in almost the same way as setting up any other modern household appliances. The basis of tuning is following the instructions supplied with each particular tuner. Consider this point to further facilitate the self-tuning of the equipment.
Purpose of the tuner and its location
For users, and there are quite a few who are completely indiscernible in radio-television electronics, the word “tuner” is perceived as difficult to fully understand.
However, there is nothing complicated in this word, since, in fact, it hides the usual sense of the receiver of the signal.
One of the many structural variations of the receiver (tuner) of a television signal from a satellite, traditionally representing the basis of a satellite system along with a “dish” - a satellite dish
In this case, we are talking about a television signal receiver broadcast via satellite.
The signal received by the tuner is converted for consistent processing by the TV. As a result, the user perceives visually on the TV screen the signal generated by the television picture.
Before proceeding with the installation of the tuner, we recommend that you read our other articles, where we described in detail how to properly install a satellite dish with our own hands and configure the “dish” on the satellite.
Correct installation of the tuner
After acquiring a television receiver, the user will need to configure it. That is, perform a series of sequential steps according to the instructions before the received signal is converted correctly and displayed on the TV screen.
Next, this process will be examined in detail with the example of the tuner of the Tricolor TV system.
Even before the start of settings, the tuner should be installed on a flat, solid surface, preferably next to the TV, but no closer than 10-15 cm from the screen panel or the back wall.
Something like this should be placed next to the television receiver. Correct installation of the tuner - when using a flat hard surface and observing the technical distances between it and the TV
The receiver module should be installed taking into account unhindered access of air to the ventilation areas, usually the lower and upper covers or side. Violation of the ventilation mode threatens overheating and malfunctioning of the device.
Usually the scope of delivery is:
- tuner module;
- control panel (remote control);
- power adapter module;
- connecting cable type 3RCA.
The tuner installed locally must be connected with the corresponding cables to the TV. Perform this operation necessarily when the network cable is disconnected.
Interfaces and Controls
The case of the standard tuner is rectangular, has a front and rear panel, where work control elements and system interfaces are located. The first, as a rule, occupy the area of the front panel. The second are located in the area of the rear case panel.
Of the control elements, the main ones are the power on / off button, the mode and channel change buttons, the information display and the user card slot.
The interface component of the modern tuner provides the end user with a variety of variations in connecting the image output source and sound broadcasting
Interfaces are usually located on the rear panel. The number of interfaces of the modern tuner is quite large and can reach more than 10:
- Under the cable RF (RF OUT) connection to the TV.
- Under terrestrial antenna cable (RF IN).
- Connection to another tuner (LNB OUT).
- Satellite dish cable connection (LNB IN).
- Composite video (VIDEO).
- For connection to a computer (USB).
- TV connection (SCART).
- TV connection (HDMI).
- Connecting sound through the tulip (AUDIO).
There, on the rear panel, a socket for the plug of the power adapter is traditionally located, sometimes mode switches and fuses.
A variant of the connecting cable (SCART / 3RSA), which can be used when connecting the output of the satellite TV tuner with the input interface of a standard television signal receiver
Connecting the tuner with a cable to a television receiver is usually done via a “SCART” cable (complete wiring) through the appropriate connector.
However, other options are not excluded, including the RF OUT signal through the standard antenna input of the TV. But in these options, the image and sound quality is reduced.
Step-by-step configuration
So, after connecting the tuner and the TV via the appropriate interfaces, you can connect the power adapter and set the network button to the “on” state.
The first launch is usually accompanied by the appearance of the “Setup Wizard” function on the TV screen. For inexperienced users this is the best tuning option.
Step # 1 - choose the language and time zone
The first screen of the “wizard” is settings according to regional standards for such parameters as the language used to communicate with the menu, audio language and time zone.
The selection of parameters on the screen of the required options is carried out using the buttons “arrow” up-down, left and right remote control.
The first setting screen, for example, the Tricolor TV system, through the options of which the user sets the necessary parameters of regional standards
Confirmation of choice - OK button. If the menu language is traditionally selected according to the regional one, the audio language, as a rule, is selected in two options - one of which supports automatic selection depending on the content.
Step # 2 - configure audio / video interfaces
At the second (screen) setup stage, you should decide on the settings that are responsible for connecting to a television receiver.
The second setting screen, by sequential choice of options of which the user sets the parameters that determine all the nuances of connecting the tuner to the television receiver
Again, using the “arrow” buttons, you should sequentially go through the list of on-screen menus.
And set the parameters on the appropriate tabs:
- Video mode - RGB or CVBS. As a rule, RGB is selected if it is connected via a “SCART” cable.
- Audio channel - TV SCART or AUDIO L / R. Mono / stereo mode is also defined here.
- Screen format - usually 16x9, less often 4x3.
- Image format - usually the default, in addition: envelope, cropped, combined.
You must also select the options in the tab Television Standard - PAL B / G, PAL D / K, PAL I, SECAM D / K). The desired standard can be defined in the documentation on the TV.
Step # 3 - configure the antenna system
Typically, the parameters of this part of the general setup menu are set by default by the satellite TV equipment provider.
The third configuration screen, by clicking on the options of which the user is given the opportunity to configure the parameters of the satellite dish (leave the default values or set custom ones)
However, individual user settings may be required:
- LNB power;
- type LNB;
- lower frequency limit;
- upper frequency limit;
- tone tone.
The screen of this part of the setup, in addition to the settings tabs, contains control bars for tuning the antenna signal.
Using one scale, the signal level is adjusted; using another scale, the decoding quality is adjusted.
Step # 4 - perform a channel search
The transition to this part of the setup is accompanied by an automatic search and detection of broadcast channels. The detected broadcasts are arranged on the screen in two lists - television channels and radio channels.
Then the function of the “Setup Wizard” is completed, and the user is informed of the corresponding message. Confirming the message, the user can go to the TV viewing functions.
The fourth tuning screen is the final main cycle of the tuning character. Confirming the displayed message, the user automatically saves all the settings
Actually, the tuning of the satellite TV tuner can be considered completed on this. All subsequent operations performed with the remote control are practically no different from those carried out with a conventional TV.
Remote control after basic settings
Depending on the tuner model, the control functionality may vary slightly. But with any tuner in the delivery set there is always a user manual, which describes all the control functions in sequence.
The result of the successful tuning of the satellite TV tuner. Now, with the help of the remote control, dozens of channels of various subjects are available to the user
Digital tuners - devices are sufficiently functional. Therefore, in addition to the standard functions of the transition from channel to channel, there is still a mass of all kinds of manipulations.
For example, all channels defined by the search can be formed in different ways, as convenient for the user:
- one column, two or three;
- quick sorting;
- listing favorites, etc.
Using the remote control, it is permissible to display a list of available audio languages and set the desired language. It is also possible to choose between mono and stereo broadcasts or, if necessary, connect subtitle accompaniment.
The remote control functionality, as a rule, supports the display on the screen of the so-called "information banners", which play a kind of television program.
The info banner also shows the current date and time, the displayed channel, TV show and other information broadcasting parameters.
Information banner, where the user is provided with an extensive set of data, including not only a television program, but also technical information on the equipment
The “Guide” functionality is seen as even more “advanced” in this regard, which, in addition to the current broadcast, also indicates a number of other broadcasts that are designated for transmission in the near-time range.
In a word, the control functions of the tuner, even the “cheapest” by the standards of the user, are a very rich set of manipulations that require a separate study.
We also offer to get acquainted with interesting ideas for the construction and tuning of a TV antenna from improvised materials.
The author of the video demonstrates the emergency tuner tuning, which may be required in various cases of failure on a previously configured receiver. Such moments happen infrequently, but can be useful in user practice:
As the user manual above demonstrates, it is quite possible to independently configure the reception of the TV signal from the satellite by the tuner. Moreover, the process is quite uncomplicated, as it might initially seem to an inexperienced user.
Each manufacturer completes the delivery with instructions and calls this user manual. Therefore, there is no need to order the setting from the master, when all this is really done with your own hands.
Perhaps you had to tune the tuner yourself and you know some subtleties that we did not mention in this material? Please share information with visitors to our site - leave your comments in the block below. There you can ask questions of interest on the topic of the article.