It is not easy, but possible, to replace leaky pipelines in the toilet room on your own. The main problems here arise due to the constraint in the bathroom. Many owners do not want to get rid of the old toilet, and replacing pipes in a toilet with already installed plumbing is still a pleasure.
We will tell you all about the rules and the specifics of replacing communications in the bathroom. We will show you what material you need to stock up on an independent home master. In the article we presented, the replacement technology is described in detail, useful recommendations are given, the observance of which will ensure the quality of the assembly.
Pipe diagnostics
Before you go to the store to buy new pipes, you need to once again think about whether such repairs should be done at all and in what volumes it should be made. If you plan to work in the toilet, which is located in a private house, then this is one situation. Here, the master master does not hurt.
But when working in a high-rise apartment, there will be many problems. When replacing the water risers in the apartment, you must coordinate your actions with your neighbors in advance. And this is not only a tribute. There are several points, forgetting about which, not long to face serious problems.
Changing the risers in the apartment toilet should be trusted only by the plumbers of the company serving the apartment building, they are better than outsiders aware of the condition of the pipes in this particular building
First, water pipes can be blocked in the basement of the entrance for several hours without asking anyone. In the afternoon, plumbing blocks of flats do this quite often. Neighbors at work during the day, most of them do not even know about a break in the water supply. However, it is not worth dismantling the sewer riser without warning.
Even if you turn off cold water in the house, it still remains in the tank of the toilet. And when the sewer riser is disassembled, all the fecal masses that will be washed away on the floors above will certainly end up in your toilet.
It is better to communicate with neighbors in advance and warn them about the work being done so that they do not use plumbing for a couple of hours. The second point is the pipes on the site in the floor. These risers are considered the most vulnerable and the most problematic. This is where metal rusts the fastest.
With the complete replacement of pipelines, they must always be removed from above and below through reinforced concrete. That is, welding and other connection of new pipes with old ones may have to be performed in neighboring apartments one floor higher and lower.
Having learned about the repair, the neighbors may well decide to change the risers at the same time with you. This will save a little on the material and the call of locksmiths who will come to block the water in the basement for the duration of the repair.
If the risers of the sewer and water supply system are changed in several apartments at once, then for each owner it will be cheaper than calling plumbers alone
The third point is the condition of the pipes. Often, plumbing and sewer risers look useless just outside. But when cutting an old iron pipeline, there are frequent cases when it is covered with rust only on the outside.
If it does not flow, then it is often not worth replacing it. Inside, everything can be perfect for him, the walls are still quite capable of lasting a couple of decades.
This happens with poor ventilation in the bathroom and toilet. Condensation builds up on metal conduits from the outside, causing rust. However, corrosion affects only the outer surface of the pipeline. Then it is only necessary to clean it with sandpaper and paint it with good paint.
Changing pipes in such a situation is just wasting money. Replacing the cast-iron riser of a sewage system with a plastic one should be done at all with its external destruction. Old cast iron is more durable and less “noisy” than modern plastic.
Options for laying pipes in the bathroom
If the toilet in the apartment or cottage is not combined with the bathroom, then special problems with the preparation of the layout of pipelines are unlikely to arise. As a rule, there is only one toilet bowl in it and there are two risers, from which it is necessary to bring a couple of pipes to this only plumbing fixture.
However, next to the wall there is usually also a kitchen and a bathroom, where pipelines are also required. But with their wiring, basically, there are difficulties when replacing pipes.
Plumbing is connected to water outlets in a rigid or flexible way (through drainage hoses), toilets are connected to the sewerage only according to the first option or corrugation
There are two technologies for laying pipes in the bathroom:
- Outdoor.
- Hidden.
The first method is simpler to execute, and the second is more aesthetically pleasing. With hidden laying of pipelines, you will have to ditch the walls, and this is dirt and extra time for preparation.
The best option is to lay the pipes in the toilet according to the external scheme, and then cover them with a decorative box. Moreover, you still have to close the risers with decor. If you leave them open, then the interior of the bathroom will look ugly.
With a hidden gasket, any leakage subsequently immediately turns into a headache. We must start all over again. You have to remove the lining, break the walls and change the pipes again.
A good option with exterior styling with decorative false walls and boxes. The latter have inspection hatches and can be easily removed if necessary, if you need to get to leaking pipelines.
Sewer pipe is laid with a slope to the riser to ensure gravity flow. According to the rules for piping pipes in bathrooms at the places of installation of plumbing fixtures, tees are inserted into it with the location of the bells towards the movement of drains.
According to construction standards, the slope of the sewer pipe is selected based on the diameter of the pipeline. The smaller the cross section, the more the latter should be tilted.
For an intra-house sewer pipe with a diameter of up to 50 mm, the slope is 3 degrees (3 cm in height for each running meter). For products with a cross section of 50-110 mm, it is recommended at 2 degrees, and for analogues in 110-160 mm - at the level of 0.8 degrees.
Plumbing is connected to the water supply:
- in a sequential manner;
- through the collector at the riser.
The collector option is more expensive, but the pressure on each water outlet with such a wiring is always the same. In this case, the water pressure in the taps and the shower does not skip when the washing machine is turned on or the toilet bowl is full.
When using the collector scheme for supplying water from the riser to plumbing fixtures, you will have to install a lot of pipes, and this whole farm is usually located just in the toilet
Water sockets are attached directly to the walls or to traverses (metal plates with holes for fasteners). In this case, the tap for the toilet in the toilet is easiest to do with a hose.
On a conducting water pipe with a cold water supply, a tee insert with an output having an external or internal thread is simply made. Ideally, pipes everywhere should be mounted in parallel, without intersecting with each other.
A stopcock is installed immediately from the riser and at the end of each water outlet. This is necessary so that, if necessary, only one plumbing fixture can be turned off to replace or repair it.
From the riser of the water supply, a ball valve is first placed, then a coarse filter, and only then a counter. The simplest and cheapest filter is a mechanical one without backwashing (with a small straight or oblique “process”, with a dirt sieve inside).
On it, from time to time it will be necessary to unscrew the lid with a wrench to wash the stainless steel mesh that accumulates sand and rust. The auto-wash filter is large. It must be connected to the sewage system, and a bypass bypass must be mounted in parallel with it.
If there is not enough space on the toilet wall, then it is better to refuse this option. All this in a complex is called an “input node”. After it there is already a pipe for connecting plumbing or a collector.
Procurement of building materials
There is no ideal building material. In each case, their own option is selected, the most suitable for specific conditions.
When replacing pipelines in a toilet, it is necessary to purchase the pipes themselves, fittings and taps for them in advance. It will not hurt to design a camouflage box in advance and purchase finishing materials for it. Then all the work will take a maximum of one day.
Sewer pipe selection
With sewer pipes, the easiest way. If the existing cast-iron riser does not have cracks and holes, then you should not change it. Otherwise, it is worth choosing plastic tees and bends.
These tubular products are light in weight and easy to install. Their connection with each other is made into a bell having a rubber cuff. The most difficult thing is to cut such pipes with a hacksaw into a segment of the desired length, not forgetting to process the end from burrs.
Separate the cast-iron parts of the sewage system carefully, this metal is very fragile - it is forbidden to hit it with a hammer or crush it with a large lever
For installation in the toilet, polymer sewer pipes from:
- PVC
- Polypropylene
- Polyethylene.
The cheapest option is polyvinyl chloride. But polyethylene and polypropylene are more resistant to household chemicals and temperature changes that occur when draining hot water into the sewer. However, in general, any of these materials is suitable for a toilet in an apartment and a private house.
Previously, cast-iron pipes were connected with cement or sulfur. In the first case, the joint will have to slowly be cracked up with a screwdriver, and in the second - to be heated with a burner.
It is necessary to carefully remove one element from another by loosening it back and forth, otherwise the bell will crack and you will have to change the pipes much more. For the connection of plastic and cast iron, an appropriate size of the rubber cuff will be enough.
Types of pipes for domestic hot water and cold water systems
Water pipes for replacement in the toilet can be taken:
- stainless steel;
- copper;
- polypropylene;
- polyethylene;
- polyvinyl chloride;
- metal-plastic.
Steel and copper pipes will have to be connected by welding (soldering), so they are rarely taken for self-assembly. Stainless steel is often used by locksmiths to replace old iron water pipes.
This option is the most reliable. The joints of new and old sections of such a pipe with high-quality welding almost never leak.
When changing toilet pipes for hot water and hot water on your own, it is recommended to choose plastic pipes, they are cheap and easily connected in various ways
For cold water in the apartment, plastic pipes should be purchased with the PN10 marking. This thin-walled version is designed for a working pressure of 1 MPa and a water temperature of up to +200C. For the HVS this is enough. For domestic hot water, an analogue with PN20 and higher is required. It has thicker walls and higher operating parameters for temperature and pressure.
Pipes PP (PP) are connected by diffusion welding using fittings and butt. The connection is one-piece. For the installation of metal-plastic compression or press fittings are used. This is the simplest material for self-assembly of the pipeline. Plus, if necessary, the water conduit can easily be disassembled to replace or insert new plumbing.
PVC are mounted on glue by butt or fitting connection. PE (PND) at home are connected by electrofusion welding or compression couplings.
Metal-plastic pipes are good at the possibility of bending in the corners of the room, they are the most plastic of all analogues from plastic. However, fittings are expensive for them. Polypropylene water pipes are cheaper to connect, but because of the large thermal expansion, they often sag on hot water. PVC is cheap, but to supply hot water you have to choose another option.
How not to make a mistake when dismantling / installing pipes
When planning the replacement of pipes in the toilet, it should be remembered that the matter is not limited to one room with a toilet. The sewer pipe will have to be completely replaced exactly.
Separately, changing sections of the water supply only in the toilet, without affecting areas in the bathroom and kitchen, is also hardly a reasonable undertaking. If you update the pipes, then immediately completely from the riser to all, without exception, plumbing devices.
In most cases, the sewer in the toilet is just a small section of the entire in-house drainage system
Separate cast-iron tees and insert new plastic bends into them exclusively by rotational movements. Cast iron is too fragile to press hard on it, much less hit it with a heavy tool. But if such a riser is planned to be completely removed, then it will not be difficult to break it into separate pieces.
All existing flexible sleeves in a braid going to the mixer or to the toilet should be thrown out immediately upon dismantling. Their service life usually does not exceed five years.
It’s better not to hesitate to change them for new ones. A similar situation with all the old valves. If she has served more than 3-4 years, then replacement is required. It’s not worth the risk.
Joints of branches and sewer pipes, as well as points of plumbing connection to it, must be sealed with cuffs or silicone, otherwise the sewer amber will fill both the toilet itself and adjacent rooms
Shaped parts must not be trimmed or modified in any way. The bell should look towards the movement of wastewater.
Without exception, all water pipes must end with stopcocks. Ideally, before each plumbing device, its own fittings with ball locking are necessary. This will greatly simplify life in the future by connecting and replacing appliances in the bathroom and kitchen.
Before closing the pipes with a box, it is necessary to pressure test the system. It is necessary to supply water through all pipelines and turn on all plumbing fixtures. And then you need to check the joints for leaks and leaks. Only in the event of their complete absence can you start finishing the toilet.
To make it easier for you to understand all the nuances of replacing pipes, we have made a selection of video materials explaining all the subtleties and tricks of the process.
Video # 1. How not to change pipes and plumbing:
Video # 2. All about the proper installation of the internal sewage system:
Video # 3. The tricks of replacing metal pipes with plastic in the combined bathroom are:
Replacing old sewer and water pipes in the toilet is easy. There are some subtleties in this work, but if desired, everything can be done independently.
Only before dismantling the existing risers, it is worth taking a closer look at them. Old pipelines are often able to last for many more years. This is especially true of the sewer system.
Want to talk about how to change communications in your own bathroom? Do you have valuable information that may be useful to site visitors who want to change their pipes on their own? Please write comments in the block below, publish your photos, ask questions about controversial issues.